Search results

Temperature is a critical factor in the fused filament fabrication (FFF) process, which affects the flow behavior and adhesion of the melted filament and the mechanical properties of the final object. Therefore, modeling and predicting temperature in FFF is crucial for achieving high-quality prints, repeatability, process control and failure prediction. This study aims to investigate the melt deposition and temperature profile in FFF both numerically and experimentally using different Acrylonitrile Butadiene Styrene single-strand specimens. The process parameters, including layer thickness, nozzle temperature and build platform temperature, were varied.

COMSOL Multiphysics software was used to perform numerical simulations of fluid flow and heat transfer for the printed strands. The polymer melt/air interface was tracked using the coupling of continuity equation, equation of motion and the level set equation, and the heat transfer equation was used to simulate the temperature distribution in the deposited strand.

The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an infrared (IR) thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the three-dimensional (3D) printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

The numerical results show that increasing the nozzle temperature or layer thickness leads to an increase in temperature at points close to the nozzle, but the bed temperature is the main determinant of the overall layer temperature in low-thickness strands. The experimental temperature profile of the deposited strand was measured using an IR thermal imager to validate the numerical results. The comparison between simulation and observed temperature at different points showed that the numerical model accurately predicts heat transfer in the 3D printing of a single-strand under different conditions. Finally, a parametric analysis was performed to investigate the effect of selected parameters on the thermal history of the printed strand.

In this paper, continuous glass tow preg-reinforced acrylonitrile butadiene styrene (ABS) composites were fabricated by using a 3D printing method, and the purpose of this study is the investigation of the fiber preimpregnation effect on the mechanical behavior of these composites. In addition, a simple theoretical approach (mixture law), which considers the elastic behavior of reinforced composites and a numerical simulation method based on finite element method (FEM), was used to predict the tensile stress–strain behavior of ABS/glass tow preg composites in the elastic region.

Different groups of preimpregnated glass tows with various ABS amounts (named 2%, 10%, 20% and 30%) were prepared by the solution impregnation method. Then, preimpregnated glass tows (prepregs or tow-pregs) were fed into the printer head along with the polymeric ABS filament to print the composites. The tensile, flexural and short beam tests were conducted to evaluate the mechanical properties of the printed composites.

The first result of using tow-pregs instead of dry tows in continuous fiber 3D printing is much easier printing, printability improvement and the possibility of printing layers with low thickness, which can further increase the mechanical properties. The mechanical test results showed all of the glass prepregs improve strength and modulus in the tensile, three-point bending and short beam tests compared with neat ABS specimens, but statistical analysis showed that ABS weight percentage in the prepregs had no significant effect on the mechanical strength of composites except for the tensile modulus. Samples containing 2%-prepreg (minimum ABS amount in the tow-pregs) showed a significant improvement in tensile modulus. In the simulation section, good agreement is obtained between the model predictions and experimental tensile results. The results show that an acceptable deviation (14%) exists between the experimental and predicted value of elastic modulus by the numerical model.

To the best of the authors’ knowledge, this is the first study showing the effects of ABS weight percentage in prepregs on the mechanical properties of 3D printed continuous fiber-reinforced composites and predicting the mechanical behavior of 3D printed composites by numerical simulation method.

The purpose of this study is to manufacture test boards for re-enacting plant or field situations where vacuum chamber for expelling gas bubbles and autoclave equipment would not be accessible. This research focuses on the examination and enhancement of tensile strength for the nanocomposites consisting of uniaxial glass fiber mats, nanoclay (NC) and epoxy.

The parameters considered are the weight content of Cloisite 15A NC, the volume of glass fiber (V_gf) and the direction of glass fibers (θ). The composites are made by hand lay-up technique and tested according to ASTM D 638 standard. Taguchi L9 orthogonal array is used to design the experiments.

The results imply that the orientation of fibers exhibited high significance with a p-value of 0.001 for the upgrade of strength. NC percentage and the volume of fiber have a low effect as the p-values obtained were 0.375 and 0.294. Confirmation tests were performed at the optimal levels of parameters and the outcomes were in the permissible range of the anticipated values of S/N ratio and mean tensile strength. The negligible effect of nanoclay is due to the lack of infusion of resin into the d-spacing of clay layers due to the low configuration settings of mixing conditions which was confirmed by XRD studies. The negligible effect of glass fiber volume is due to the void content and lack of stress transfer between fibers uniformly due to the void content and improper mixing of nanoclay.

The limitation of this study is that a low-speed mechanical stirrer was used to mix NC in the epoxy and the mixture was not subjected to vacuum and ultrasonication for degassing and deagglomeration.

These composites can be used as substitute materials in place of metallic parts in the aerospace and automobile sector. These composites can be used in civil structures instead of steel and concrete, which have low strength-to-weight ratio and where the requirement of strength is in the range of 60 to 390 MPa.

The composites can be used in a variety of applications, for example, structural works, automotive panels and low-cost housing.

This research gives an idea about the combined contribution of NC, V_gf and “θ” to the improvement of tensile strength of the glass-epoxy composite.

The low resistance against penetration of water, oxygen and the other corrosive ions through the paths of coating is one the most important problems. So, protective properties of coating such as polyester must be promoted. Recently, the use of nanoparticles in the matrix of polymer coating to increase their protection and mechanical properties has been prospering greatly. The purpose of this study is to improve the corrosion resistance of the polyester powder coating with ZnO nanoparticles. The ZnO nanoparticles have been synthesized by hydrothermal method in a microwave. Using polyester – ZnO nanocomposite coating as powder – combining them by ball milling process and coating them by electrostatic process are innovative ideas and have not been used before it.

Polyester powder as the matrix and ZnO nanoparticles as reinforcing were combined in three different weight percentage (0.5, 1, 2 Wt.%), and they formed polymer nanocomposite by ball milling process. Then, the fabricated nanocomposite powder was applied to the surface of carbon steel using an electrostatic device, and then the coatings were cured in the furnace. The morphology of synthesized zinc oxide nanoparticles was investigated by transmission electron microscope. Also, the morphology of polyester powder and fabricated coatings was studied by scanning electron microscope. The effects of zinc oxide nanoparticles on the corrosion resistance of coated samples were studied by electrochemical impedance spectroscopy (EIS) test at various times (1-90 days) of immersion in 3.5 per cent NaCl electrolyte.

Scanning electron microscopy (SEM) results reveal that there are no obvious crack and defects in the nanocomposite coatings. In contrast, the pure polyester coatings having many cracks and pores in their structure. According to the EIS results, the corrosion resistance of nanocomposite coating compared to pure coating is higher. The value obtained from EIS test show that corrosion resistance for coating that contains 1 Wt.% nanoparticle was 32,150,000 (Ωcm²), which was six times bigger than that of pure coating. In addition to providing a barrier against diffusion of electrolyte, ZnO nanoparticles act as a corrosion inhibitor and, thus, increases the corrosion resistance. The corrosion resistance of coating containing 0.5 Wt.% nanoparticles was lower as compared to that of 1 Wt.% nanoparticles. The low content of nanoparticles caused partial covering of the porosity of coating which in turn leads to provide weaker barrier properties. The increase in quantity of nanoparticles from 1 to 2 Wt.% also caused a decrease in corrosion resistance which is attributed to the agglomeration of nanoparticles.

The results of this study indicated the significant effect of ZnO nanoparticles on the protective performance and corrosion resistance of the polyester powder coating. Evaluation of coating surface and interface with SEM technique revealed that nanocomposite coating compared with pure polyester coating provided a coating with lower number of pores and with higher quality. The EIS measurements represented that polymeric coating that contains nanoparticles compared to pure coating provides a better corrosion resistance. In addition to providing a barrier against diffusion of electrolyte, ZnO nanoparticles act as a corrosion inhibitor and thus increase the corrosion resistance. The corrosion resistance of coating containing 0.5 Wt.% nanoparticles was lower as compared to that containing 1Wt.% nanoparticles. The low content of nanoparticles caused partial covering of the porosity of coating which in turn leads to provide weaker barrier properties. The increase in quantity of nanoparticles from 1 to 2 Wt.% also caused a decrease in corrosion resistance which is attributed to the agglomeration of nanoparticles.